In this article below you might get a good deal of extremely good facts around Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard task. If the old tub is readily easily accessible, the job can relocate easily; if you have to open a wall to eliminate the old bathtub and position the new tub, the job is a lot harder. In either instance, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the task and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This article will certainly help you mount a brand-new bath tub in your washroom if you have actually currently gotten a brand-new bathtub and also do not require to alter the plan of your previous water system pipelines.
Your devices and material list need to consist of the following:
Preparing for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bath tub in the required placement. The wooden boards are valuable in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water system as well as examine all joints and also new pipework for leaks as well as tighten them if needed. Load the bath tub and also inspect the overflow outlet as well as the typical electrical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub must wait up until the tub has actually been utilized a minimum of once as this will settle it into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers remain in area between the tap as well as the sink. Secure the faucet in position with the producer offered backnut. As soon as the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in difficulties with moisture and possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks so much for taking the time to browse our short article. Enjoyed our piece? Please share it. Let other people discover it. Thank you so much for going through it.
Get A Free Estimate